Hello,
I have the following:
RPI 4 Model B 4 GB
RPI Camera Module 3
Linux ender3 6.6.20+rpt-rpi-v8 #1 SMP PREEMPT Debian 1:6.6.20-1+rpt1 (2024-03-07) aarch64 GNU/Linux
"Debian GNU/Linux 12 (bookworm)"
rpicam-apps build: 6202c09b2bfa 16-02-2024 (17:15:37)
libcamera build: v0.2.0+46-075b54d5
python3-picamera2/stable,stable,now 0.3.17-1 all [installed]
libcamera-hello --list-cameras
Available cameras
-----------------
0 : imx708 [4608x2592 10-bit RGGB] (/base/soc/i2c0mux/i2c@1/imx708@1a)
Modes: 'SRGGB10_CSI2P' : 1536x864 [30.00 fps - (0, 0)/0x0 crop]
2304x1296 [30.00 fps - (0, 0)/0x0 crop]
4608x2592 [30.00 fps - (0, 0)/0x0 crop]
My installation is relatively recent. I set up my RPI to run Klipper on my 3d Printer and I had wanted to add the camera to my setup. I had everything turned off and made sure the connections were set up properly. I was under the impression that it would be auto-recognized. After searching the internet for help, I installed some libcamera packages thinking that would do the trick but it did not. I tried a few other suggestions and I'm not sure if I messed anything up. I finally found my way to the official forum and hope that I have provided the proper information. I also tried an additional ribbon cable.
I believe I covered all the instructions from viewtopic.php?t=362707 with the exception of a fresh install of the OS. I will do it if needed but would love not to have to setup everything again.
Please let me know if there is any additional info need, but any assistance would be greatly appreciated.
Thanks!
I have the following:
RPI 4 Model B 4 GB
RPI Camera Module 3
Linux ender3 6.6.20+rpt-rpi-v8 #1 SMP PREEMPT Debian 1:6.6.20-1+rpt1 (2024-03-07) aarch64 GNU/Linux
"Debian GNU/Linux 12 (bookworm)"
rpicam-apps build: 6202c09b2bfa 16-02-2024 (17:15:37)
libcamera build: v0.2.0+46-075b54d5
python3-picamera2/stable,stable,now 0.3.17-1 all [installed]
libcamera-hello --list-cameras
Available cameras
-----------------
0 : imx708 [4608x2592 10-bit RGGB] (/base/soc/i2c0mux/i2c@1/imx708@1a)
Modes: 'SRGGB10_CSI2P' : 1536x864 [30.00 fps - (0, 0)/0x0 crop]
2304x1296 [30.00 fps - (0, 0)/0x0 crop]
4608x2592 [30.00 fps - (0, 0)/0x0 crop]
My installation is relatively recent. I set up my RPI to run Klipper on my 3d Printer and I had wanted to add the camera to my setup. I had everything turned off and made sure the connections were set up properly. I was under the impression that it would be auto-recognized. After searching the internet for help, I installed some libcamera packages thinking that would do the trick but it did not. I tried a few other suggestions and I'm not sure if I messed anything up. I finally found my way to the official forum and hope that I have provided the proper information. I also tried an additional ribbon cable.
I believe I covered all the instructions from viewtopic.php?t=362707 with the exception of a fresh install of the OS. I will do it if needed but would love not to have to setup everything again.
Please let me know if there is any additional info need, but any assistance would be greatly appreciated.
Thanks!
Statistics: Posted by HardcoreJawa — Mon Mar 25, 2024 1:56 am — Replies 0 — Views 4
