Advanced users • Configuring the Rapsberry Pi 5 power switch functionality
Is there any way to configure the action on the power switch on a Raspberry Pi 5?The default functionality is a double press to power off. I would like it to be a single press.The reason is because I...
View ArticleCompute Module • Super6C CM4 does not detect NVMe
Hi all,I would appreciate any insight into troubleshooting my NVMe problem. Not trying to boot, just want the devices attached for data.I purchased a Super6C board with 5xCM4108000 compute modules,...
View ArticleRaspberry Pi OS • Not able to invert mouse
Hi. I have 27" monitor that I have turn left. The problem is that my mouse is inverted. (im connected via RealVNC)I first run this command:xinput listWARNING: running xinput against an Xwayland...
View ArticleGeneral discussion • USB connection to serial device
I am trying to use a Raspberry Pi 4 to communicate to a temperature controller made by Lakeshore (model 240-8P).The manual gives me the following information:Digital I/O – USBFunction: Emulates a...
View ArticleClik here to view.
Troubleshooting • Camera not detected: Raspberry pi 5 and Camera module V3
Raspberry pi 5 and Camera module V3camera_auto_detect=1 has been setup in the config.txtHowever, the following command is showing the error with no camera detected message. $...
View ArticleTroubleshooting • Running Python File At Startup - Lock Up Detect
I have a zero 2 w running my hot tub.During debug I leant that the IO seems to hold its last state if the processor hangs. I've since added watchdog to try to unlock the PI VIA reboot.Next steps1)...
View ArticleBeginners • Using threading.Event to control my GPIO Pins
Hi,Can somebody please help me understand how to apply threading to my Raspberry Pi Project?I am using Raspberry Pi 4 with the latest Raspberry Pi OS.I have a button and an MFRC522 RFID reader...
View ArticleSDK • Issue with Watchdog Scratch Registers
I'm trying to figure out why my watchdog scratch registers don't have the correct value in them after the watchdog reset. I must be missing something basic on how to use them. Here is my code: Code:...
View ArticleGeneral • Driving two wires via PIO with bits from different bytes at the...
I have two pins that want to send data, and I want to synchronize these sends with a clock that pulses the cycle after I send each bit, and another pin that pulses once after the 8th bit is sent on...
View ArticleBeginners • pi camera
hello, running a pi 4 8bg on raslbian os 64-bit. just ordered a pi camera rev 1.3. plugged it into proper connector but I cannot enable it on interface in raspi-config. camera option is not available....
View ArticleTroubleshooting • hdd crash
Hello,I've try to search a response but without success.So there is my problem:I've bought a raspberry pi 5 and try to connect a HDD 8To self powered but each time I start it the pi freeze. Unable to...
View ArticleTroubleshooting • Raspberry PI 5 with 7” Touchscreen
I have just bought a PI 5 8gb and opted for a 7.1” touchscreen without a keyboard or mouse. The problem I am encountering is that when ever passwords are required I am not always presented with a...
View ArticleTroubleshooting • Raspberry Pi 4 Model B Stopped Working Please help
I have a raspberry 4 model B that has quit working. I am not sure what to do because ive tried Different SD cards. the cards I have tried i know work on my other Pi's so its not an sd card problem....
View ArticleClik here to view.
Camera board • Raspberry Pi 5 with module 3 camera Device timeout detected,...
Hello I have Raspberry Pi 5 and picamera module 3. I am using my camera without any problem nearly 2 months. But yesterday my camera gives an error and shows a black image:I bought and tried with new...
View ArticleClik here to view.
Camera board • Raspberry Pi 5 with module 3 camera (imx708) Device timeout...
Hello I have Raspberry Pi 5 and picamera module 3(imx708). I am using my camera without any problem nearly 2 months. But yesterday my camera gives an error and shows a black image:I bought and tried...
View ArticleTroubleshooting • Boomaga not sending jobs to printer
I have:HP1022 printerRPi 3b running Raspberry Pi OSI am able to print from chrome through the regular print system. However, when I use Boomaga no jobs are sent to the printer. The printer job window...
View ArticleGeneral • Raspberry Pi Pico crashes after multiple reboots
Hello, I had 2 prototypes working well, until my MQTT broker had a failure, and when it could not connect and the watchdog went into action, after several days (3 or 4) of restarting every 25 or 30...
View ArticleGeneral discussion • Raspberry Pi 3A+ has silkscreen (c) date of 2022 ?
Pimoroni recently had a sale. with 3A+ reduced in price so thought I'd get one as I'm sure to find a use for it.Noticed that the (C) date printed on the board is 2022. Since the 3A+ came out in 2018...
View ArticleBeginners • Raspberry Pi 5 Audio?
Hello there, I’ve had my raspberry pi 5 for around 2 months now, and I have this speaker that I got when taking apart old technology. It looks like a really small laptop speaker, and has a blue and...
View ArticleGeneral discussion • USB Drives Problems after upgrading
Hi, I'm having trouble using my USB drives on raspberry pi 5. You can read more about everything that happened before in this post viewtopic.php?t=368289. The thing is that I had to erase that memory...
View Article